Special Feature: Digital Power supply

Special Feature: Digital Power supply Sanken Power IoT


Product Description of MD660x Series MCU for Digital Power Supply


MD660x Series are 8-bit MCUs optimal for power control applications including digital power supply.

Equipped with rich analog functions, high-performance DSP, high-resolution PWM, and so on, making it possible to build high-efficiency high-performance power control applications using their low-power and strong system support functions.

Contents of Product Description

block diagram

Four Features of MD660x Series


  • Feature 1: Rich analog functions


    A high-speed 10-bit A/D converter, a high-precision 12-bit A/D converter, a D/A converter, a high-speed comparator, and a general-purpose operating amplifier and so on are incorporated.
    These analog function modules or these modules and external pins can also be wired mutually using a programmable internal wiring network.

  • Feature 2: High-performance operation functions with three core processors; CPU and TinyDSPs


    MD660x Series have two units of 16-bit TinyDSP in addition to the main CPU.
    System processing by the CPU and arithmetic processing by TinyDSP can be performed in parallel respectively.
    TinyDSP supports division in addition to MUL (multiplication) and MAC (multiply & accumulation).


  • Feature 3: High-resolution PWM function


    For the PWM output waveform, duty ratio and cycle can be set up in a resolution of 1ns.
    This function can add dead time automatically and perform high-speed response such as duty cut or cycle cut of the PWM waveform in synchronization with external events such as a comparator.

  • Feature 4: Automatic data transfer function among peripheral registers (DSAC)


    Data can be transferred automatically among the registers of the built-in peripheral modules.
    For example, by transferring data automatically among the A/D converter, TinyDSP units, and PWM unit, feedback control can be executed without the CPU.
    During such feedback control, the CPU focuses on system processing such as abnormality detection or communications processing.

Product Specifications


Item MD6602 MD6603
Common Power Supply Voltage/Operating Frequency Both the digital DVCC and analog AVCC can operate with a 3.3 V single power supply/50 MHz (max.).
Power Consumption (Typ.) Digital: 165 mW, Analog: 20 mW Digital: 165 mW, Analog: 20 mW
Package QFN-40(6×6、P0.5)
LQFP-64(10x10, P0.5)
QFN-40(6×6, P0.5)
Analog Function Analog Internal Wiring Programmable (for example, inserting an operating amplifier between the A/D comparator and external pins) -
10-bit A/D Converter 2 units, 4 MSPS/unit, dual sampling -
12-bit A/D Converter 1 unit, 1 MSPS/unit 2 unit, 4 MSPS/unit
D/A Converter 10-bit voltage output × 4 ch 8bit × 6ch for comparator reference
Analog Comparator 6 units, high-speed response 6 units, high-speed response
General-purpose OPAMP 4 units, standalone/unity gain selection 2 units, standalone mode/unity gain selection
Voltage Reference 1.2 V output, middle point GND output
Temperature Sensor Voltage output, read by the A/D converter
Digital Function 8-bit 8051 CPU 8051/8052 instruction compatible, instruction execution cycle: 1 cycle (min.), 3 cycles (avg.)
1-wire Debug I/F R/W in the internal resources, execution control, break point, and writing in the flash memory are possible by one signal only.
Flash Memory 32 KB, with a cache memory and protection function 32 KB, with a cache memory and protection function
Built-in RAM 1 KB (+CPU direct connection RAM × 256 bytes) 1.5 KB (+CPU direct connection RAM × 256 bytes)
TinyDSP 2 units, enhanced by the saturation instruction and constant-number register and so on. 2 units, enhanced by the saturation instruction and constant-number register and so on.
EPU - 1 unit, 16-bit, 6 thred, 16 input/output events per thread
High-resolution PWM 2-phase PWM × 4 sets output, 1ns resolution (duty/cycle), Duty Cut, Cycle Cut are usable. 2-phase PWM × 4 sets output, 1.04ns resolution (duty/cycle), Duty Cut, Cycle Cut are usable.
DSAC 16 ch, DMA function among peripheral registers 16 ch, DMA function among peripheral registers
16-bit Timer 4 units, 16-bit counter, Output Compare/Input Capture function 4 units, 16-bit counter, Output Compare/Input Capture function
SPI/I2C/UART 1 unit each, external terminals are independent each other 1 unit each, external terminals are independent each other
GPIO( 5V tolerant for digital ) Same as on the left except for LQFP-64.
LQFP-64: Digital×26, Analog×20
Digital ×14, Analog ×14
Interrupt Controller Independent vectors for each interrupt source, interrupt priority of 2 levels, interrupt input can be set up on all the GPIO.
WDT 1 unit, reset or interrupt generation
LVD Built-in low voltage detection circuit
POR Built-in power on reset circuit
IRC Internal Reference Clock Generator (10 MHz) Internal Reference Clock Generator (12.5 MHz)
PLL The frequency of an external (crystal) clock/IRC clock is multiplied by 4 times (40 MHz, max.). The frequency of an IRC clock is multiplied by 4 times (50 MHz, max.).
Item MD6602 MD6603


Browse Products list
MCUs for Digital Power Supply

Development Environment of MD660x Series


Integrated Development Environment “MD-Studio”

An integrated development environment for CPU program development, MD-Studio, is provided for free.
This environment supports various functions such as an editor, C-compiler, or debugger.

【Outline】

  • Editing of source programs and management of projects
  • Building of C-programs and assembly programs (Compiler/Assembler/Linker)
  • Erasing, writing, and protection of the flash memory
  • Debugging functions (execution): Run/STOP/STEP execution, break point specifying on the C-source code.
  • Debugging functions (reference): Disassembling, display and change of the memories/registers, display values of variables in a C-source code.
  • TinyDSP assembler simulator function


Compact Debug Interfaces “OCD I/F Board”

An OCD I/F board, which connects between a PC and the target board at the time of program development, is provided.
No expensive ICE or JTAG debuggers are required.
Programming the flash memory and debugging can be performed by connecting a PC with USB and the target board basically with 3 wires only.
The circuit schematics for the OCD I/F board is also available.


Ultra-compact Evaluation board “CHEWING GUM”

An ultra-compact evaluation board of MD6602 as a bare MCU device, CHEWING GUM, is provided.

【Outline】

  • 53 mm×18 mm small size
  • The MCU terminal signals are connected to the 2.54 mm pitch terminals. (Can be mounted on a breadboard, and so on.)
  • Two-color LED and a reset button are mounted.
  • Bus power operation by connecting to a PC via USB cable.
  • Built-in debug interface circuit.
  • In the Integrated Development Environment “MD-Studio”, the flash memory can be programmed and application program can be debugged.
  • Circuit schematics and sample programs are included.

MD660x Product list / Inquiry Form

MD660x Product list
Click Here

Design Support
Click Here

For inquiries, please use the inquiry form.





Questions or Comments?

Please feel free to contact us if you cannot find the desired product from the lineup.